Martin Lighting

Martin Atomic 3000 LED

The Atomic™ 3000 LED is the perfect blend of a traditional strobe and cutting-edge LED technology.

Specifications

Strobe: 0.289 - 16.667 Hz, variable flash rate, intensity and duration
Special effects: Blinder, ramp up/down, random flash, lightning. spikes, pre-programmed FX
Aura (secondary LED array illumination) color mixing: RGB

Control systems: DMX, RDM
Setting and addressing: Control panel with backlit monochrome graphic display
DMX channels: 3/4/14
DMX compliance: USITT DMX512-A
RDM compliance: ANSI/ESTA E1.20 RDM
Transceiver: RS-485
Firmware update: via USB type A memory device or via DMX using Martin Companion

Max. total output: 180,000 lumens*
Beam (strobe) array: Light source: 228 x Cree XLamp XP-L, 10 W white LEDs (color temperature 5,700 K); Resolution: 8-bit; Dimming, above 16.7% output intensity: Current-controlled, flicker-free; Dimming, below 16.7% output intensity: PWM (refresh rate 6,000 Hz); Binning: Tight color and flux binning; Minimum LED lifetime: 50,000 hours**
Aura (backlight) array: Light source: 64 x Osram RGB LEDs; Resolution: 8 bits per color plus 8-bit dimming; Dimming: PWM (refresh rate 1,001 Hz); Binning: Tight color and flux binning; Minimum LED lifetime: 50,000 hours**; *For full photometric data, click on Photometrics in menu bar; **To >70% output, figure obtained under manufacturer’s test conditions

Mounting points: Two pairs of quarter-turn fastener points, M12 holes in adjustable bracket
Location: Indoor use only, must be fastened to structure or surface
Orientation: Any
Minimum distance to combustible materials: 200 mm (8 in.) from fixture
Minimum distance to illuminated surfaces: 1 m (3 ft. 4 in.) from fixture

AC power: 100-240 V AC nominal, 50/60 Hz; Power supply unit: Auto-ranging electronic switch mode; Typical half-cycle RMS inrush current at 230 V, 50 Hz: 17.7 A; Typical earth-leakage current: 0.18 mA; Power Factor: 0.98 @ 100 V , 0.96 @ 120 V , 0.89 @ 208 V , 0.88 @ 230 V , 0.87 @ 240 V; Max current draw: 8.4 A @ 100 V / 120 V , 3.9 A @ 208 V / 230 V / 240 V; Typical current draw: 6.8 A @ 100 V , 5.7 A @ 120 V , 3.5 A @ 208 V , 3.2 A @ 230 V , 3.1 A @ 240 V *; Power Consumption; Maximum: 740 W; Typical: 663 W *; Idle: 25 W *; * Measurements made at nominal voltage. Allow for a deviation of +/- 10%. Allow for peak currents that exceed these figures when using the blinder effect.; Typical: full output white, regulated fan speed.; Idle: no output, regulated fan speed.

Cooling: Forced air (temperature-regulated, low noise, user-definable fan settings)
Maximum ambient temperature (Ta max.): 40° C (104° F)
Minimum ambient temperature (Ta min.): 5° C (41° F)
Typical heat dissipation (calculated, +/- 10%): 2270 BTU/hr.

EU safety: EN 60598-2-17 (EN 60598-1), EN 62471, EN 62493
EU EMC: EN 55015 Class B, EN 61547, EN 55032, EN 55035, EN 61000-3-2 Class A, EN 61000-3-3
US safety: UL 1573
US EMC: 47 CFR 15 Class A
Canadian safety: CSA E598-2-17 (CSA E60598-1)
Canadian EMC: ICES-003 Class A
Australia/NZ: RCM
United Kingdom: UKCA
Thailand: TIS

Power connectors: Cable Connector, Neutrik PowerCON TRUE1 NAC3FX-W (female): P/N 91611789
Power cables: Power Input Cable, H07RN-F, 2.5 mm2, bare ends to TRUE1, 1.5 m (4.9 ft.): P/N 91611797; Power Input Cable, H07RN-F, 2.5 mm2, bare ends to TRUE1, 5 m (16.4 ft.): P/N 91611786; Power Input Cable, SJOOW, 12 AWG, bare ends to TRUE1, 1.5 m (4.9 ft.): P/N 91610173; Power Input Cable, SJOOW, 12 AWG, bare ends to TRUE1, 5 m (16.4 ft.): P/N 91610174
Installation hardware: Half-coupler clamp: P/N 91602005; G-clamp (vertical hanging installation only): P/N 91602003; Quick trigger clamp (vertical hanging installation only): P/N 91602007
Safety Cable, SWL 60 kg, BGV C1 / DGUV 17, black: P/N 91604006
Safety Cable, SWL 60 kg, BGV C1 / DGUV 17, silver: P/N 91604007
Atomic Colors gel scroller: P/N 91611086